{"product_id":"hydramaster-gasket-recovery-tank-old-style-000-057-043","title":"Hydramaster GASKET, RECOVERY TANK – OLD STYLE 000-057-043","description":"\u003ch1 class=\"product_title entry-title elementor-heading-title elementor-size-default\"\u003eGASKET, RECOVERY TANK – OLD STYLE\u003c\/h1\u003e\n\u003cp\u003e\u003cmeta charset=\"utf-8\"\u003e\u003cspan\u003eGASKET, RECOVERY TANK – OLD STYLE\u003c\/span\u003e\u003c\/p\u003e\n\u003ch1 style=\"text-align: center;\"\u003e\u003cspan\u003e\u003cmeta charset=\"utf-8\"\u003e000-057-043\u003c\/span\u003e\u003c\/h1\u003e\n\u003cp\u003eRecovery tank lid gasket for HydraMaster truckmounts. HydraMaster part number 000-057-043, listed as\u003cspan\u003e \u003c\/span\u003e\u003cem\u003eGasket, Recovery Tank\u003c\/em\u003e\u003cspan\u003e \u003c\/span\u003eand, in HydraMaster's own suggested spares schedule, as the\u003cspan\u003e \u003c\/span\u003e\u003cem\u003ewaste tank gasket kit\u003c\/em\u003e.\u003c\/p\u003e\n\u003cp\u003eIt is supplied as a length. In most cases it will be longer than you need — cut it to suit your machine.\u003c\/p\u003e\n\u003ch2\u003eWhat it fits\u003c\/h2\u003e\n\u003cp\u003eThis is the closest thing HydraMaster has to a universal part. Their suggested spares schedule lists it against every machine in the range:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eBoxxer 421 and Boxxer 427\u003c\/li\u003e\n\u003cli\u003eCDS 4.6, CDS 4.7 and CDS 4.8\u003c\/li\u003e\n\u003cli\u003eCTS330 and CTS450\u003c\/li\u003e\n\u003cli\u003eMAXX 450D \/ 470D\u003c\/li\u003e\n\u003cli\u003eSpitFire 3.2 and SpitFire 4.0\u003c\/li\u003e\n\u003cli\u003eCrossfire 4.2\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eImportant:\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003e\u003cem\u003e\u003cspan style=\"text-decoration: underline;\"\u003e\u003cspan style=\"color: rgb(255, 42, 0); text-decoration: underline;\"\u003e\u003cstrong\u003eit suits HydraMaster machines that do not have a MaxxAir tank. If your machine has the MaxxAir arrangement, ask us before ordering.\u003c\/strong\u003e\u003c\/span\u003e\u003c\/span\u003e\u003c\/em\u003e\u003c\/p\u003e\n\u003ch2\u003eWhich truck mount waste tank tank do you have?\u003c\/h2\u003e\n\u003cp\u003eHydraMaster changed the waste tank sealing arrangement between generations, and the two arrangements do not take the same gasket.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eOlder tanks\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003e— the gasket is pushed onto the edge of the tank itself. That is this part, 057-043.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eNewer tanks\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003e— a flat gasket sits against the underside of the lid. Those take the pre-cut lid gaskets \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eCheck the tank before you order. If the seal pushes onto the tank edge, this is the part. If it sits flat on the lid, it is not.\u003c\/p\u003e\n\u003ch2\u003eWhy the recovery tank seal matters\u003c\/h2\u003e\n\u003cp\u003eEverything the machine recovers depends on the tank holding vacuum. A lid gasket that has gone hard, taken a permanent set, or lifted at a corner is a leak in the largest, lowest-pressure part of the vacuum path — and it costs you lift at the wand on every job.\u003c\/p\u003e\n\u003cp\u003eIt is also the leak operators most often miss, because the machine sounds and looks normal. The vacuum gauge tells the story: if lift is down and the gauge is not climbing, air is getting in somewhere it should not, and the lid is the first place to check.\u003c\/p\u003e\n\u003ch2\u003eFitting advice\u003c\/h2\u003e\n\u003cp\u003eClean the channel properly. Old adhesive, dried slurry and fibre under a new gasket will hold it off the sealing face and you will not get the seal back.\u003c\/p\u003e\n\u003cp\u003eCut it slightly long rather than short, and butt the join on a straight run rather than at a corner. A join at a corner is where the seal will fail first.\u003c\/p\u003e\n\u003cp\u003eFit it relaxed. Stretching the gasket into place makes it look right on the bench and pull back into a gap after a few heat cycles.\u003c\/p\u003e\n\u003ch2\u003eFrequently asked questions\u003c\/h2\u003e\n\u003ch3\u003eHow much do I get?\u003c\/h3\u003e\n\u003cp\u003eIt is supplied as a length intended to be cut to fit. It is normally longer than a single machine needs.\u003c\/p\u003e\n\u003ch3\u003eWill it fit my machine?\u003c\/h3\u003e\n\u003cp\u003eHydraMaster list it against every truckmount in the range except machines with the MaxxAir tank. If yours has a MaxxAir tank, ask us first.\u003c\/p\u003e\n\u003ch3\u003eDo I need adhesive?\u003c\/h3\u003e\n\u003cp\u003eFollow the arrangement on your machine — check what was fitted before you strip it. Do not glue a gasket into a channel designed to hold it mechanically.\u003c\/p\u003e\n\u003ch3\u003eHow do I know the seal has gone?\u003c\/h3\u003e\n\u003cp\u003eVacuum lift down at the wand with no rise on the vacuum gauge, or a gasket you can compress with a thumbnail and it stays compressed.\u003c\/p\u003e\n\u003chr\u003e\n\u003cp\u003eChasing a vacuum loss? Tell us the machine and the symptoms and we will help you work through the likely causes before you start buying parts.\u003c\/p\u003e\n\u003chr\u003e\n\u003cp\u003e\u003cbr\u003e\u003c\/p\u003e","brand":"CLEANING DEPOT STORE","offers":[{"title":"Default Title","offer_id":46563694182550,"sku":null,"price":70.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1880\/8187\/files\/Gasket-Recovery-Tank_000-057-043.webp?v=1789588368","url":"https:\/\/cleaningdepotstore.com\/products\/hydramaster-gasket-recovery-tank-old-style-000-057-043","provider":"CLEANING DEPOT STORE","version":"1.0","type":"link"}